Can anyone post pictures on how to build rudder stearing linkage?
thanks in advance for your help!
Morrie
Can anyone post pictures on how to build rudder stearing linkage?
thanks in advance for your help!
Morrie
morrie,
The easiest way is to use a teleflex control cable, avaible from Chuck at Airboat Pro's., or any airboat dealer.
I made up two systems using electrical tubing (EMT), and sperical rod ends. After I finished each one, I wished I had done them differently. It was a little cheaper (not much), but a lot more time consuming.
Point I am trying to make is, each boat will require a little different design, so you need to figure out your own, or get someone to take a look at your setup and suggest something that will work best.
The main thing is, a left hand control stick should turn the boat left when you pull it back. A right hand control should be opposite. Also, keep the cable or control rods off to the side, and out of the way, so they don't get stepped on.
Good luck, Dave
IF YOU WON'T STAND BEHIND OUR TROOPS, THEN JUST STAND IN FRONT OF THEM!
Thanks Dave, sounds like good advice. You, Buster, Chuck and Papee have helped me alot, I am very gratefull to all!
Chuck I hope you are able to help me out. What information do you need to make this happen?
Morrie
Hey morrie, I will try to get some pictures of our steering today and get them posted tonight.
Thanks, Chuck
Thanks Chuck, I'm assuming that you sell all that I need? I'll try to post pictures of my progress today.
thanks again...
Morrie
Hey Morrie,
If you want to mke your stearing out of Pipe instead of teliflex. Check out my build under Builds/ Boggers Rotax Rig/ page two. I have a picture or two of how to set up stearing using EMT pipe. It's a little cheeper but I think the teliflex stearing is pobably a little smother. Mine ain't bad with the heim jionts though. Good luck with your build.
Bogger
Boat specs:
Hull, 116 fiberglass
Bottom, Frog spit
Motor, Rotax 532 dual carb
65 ponies to push with
Reduction, 2.58/1
Prop, IVO 62in.3blade adjustable
Rigging, 0.5 and 0.75 emt
All still under construction
Thanks for the feedback, thats a nice boat you built.
Morrie
Hey morrie, i tried to upload pictures twice to the gallery and it said they were uploaded but then would not let me put in info on them. I will try from the post.
Well that don't work either. Maybe Papee can check the gallery.
Thanks, Chuck
Chuck, do you think it will work if you sent them to my web address?
I will try that tonight morrie.
Chuck
hello Chuck, any luck on the pictures?
thanks, Morrie
Hey morrie, i sent you the pictures in an email. I hope they help you.
Thanks, Chuck
Got them, thanks Chuck. do you sell the cable?
Morrie
Morrie, he does sell the cable in any length you need. I have one coming from him and will be doing my steering over shortly.
Please check out our YouTube channel and subscribe! Our YouTube Channel helps fund the site. Check it out at https://www.youtube.com/channel/UCTv...FrJP7yQVFVZnyA
Hello Papee, do you know what the cost is per foot?
thanks, Morrie
morrie,
I ain't speaking for Chuck. This is just how I understand it.
I don't think it's a "by the foot" kind of number. I think that the price is pretty much the same, regardless of length (within reason). I "think" that Chuck takes a standard Teleflex steering cable, cuts it to the length you need, and puts his end back on it.
That's just the way I understsand it. You really need to talk with Chuck.
Give him a call. I promise that he'll do you right, and help you out any way that he can.
His number is: 352-330-1015
Duane
A KWAZY old Southerner... and darn PROUD of it.
Airboat Pros MiniPro 116 / Frog Spit
SS rigging - with side by side seating
Teledyne 4A084-4 engine
Solex H30/31 Carb
Arrow Prop 1.73:1 reduction
67" Whirlwind 2 blade Mini Prop
under construction
Hey Papee, Your steering cable and your starter/generator kit will go out tomorrow. We got the pulley sleved to 7 inch dia so it will crank better.
Hey morrie. all the steering cables under 14 ft are $ 185.00.
Thanks, Chuck
Whoo hooo looks like I have some work to do. Thanks Chuck, I'll send the old pulley down along with anything else I need to include. I'll pull the boat in the garage tomorrow and get it started.
Please check out our YouTube channel and subscribe! Our YouTube Channel helps fund the site. Check it out at https://www.youtube.com/channel/UCTv...FrJP7yQVFVZnyA
Papee,
I want to see what Chuck has came up with.
Back when the weather was still warm enough, I tried my starter, but it didn't work very well. Actually, it was a dismal failure. Don't tell Buster though. (He knows already )
When the weather warms up a bit, I've got another idea or 2 to try.
Duane
A KWAZY old Southerner... and darn PROUD of it.
Airboat Pros MiniPro 116 / Frog Spit
SS rigging - with side by side seating
Teledyne 4A084-4 engine
Solex H30/31 Carb
Arrow Prop 1.73:1 reduction
67" Whirlwind 2 blade Mini Prop
under construction
Hey Papee, all we need is the pully as a core so we can get another one made.
Thanks, Chuck
Bookmarks