will time for an update i made some mod to the starter generator i removed the front cover and drilled 3 3/8th hole in the cover and removed the brush covers and so far its doing great it dont get...
Type: Posts; User: dak10
will time for an update i made some mod to the starter generator i removed the front cover and drilled 3 3/8th hole in the cover and removed the brush covers and so far its doing great it dont get...
hi all my wife said no playing on the air boat till the honeydo list is done I told her that aint fair cuz her list is 2 blocks long but if momma aint happy we know what will happe
well i got another gen. for now did some mod's to the generator so lets see what happens it work good some parts from here an there now we go again,got 2 hrs so far on this one
here is something i forgot to say the steel 3/16 fuel line from the pump is to small for what we demand i put a 5/16 rubber line from the pump to the carb,i do think at iceing came come from lean...
cool but i think if it is iceing then there is water in the fuel it don't make sence to me in the cold states water is the problem and the carb that comes on the 084 is ok for now i have the solex...
no one hit on this but i found out that the primer ball was sucking flat and we all know what happens then, just a though i removed mine and my high speed bogging went away ,an if u r useing a ele....
will i have not yet found a starter that ia dependable
i think it (starter gen) works great for about 10 or starts THEN it get hot from no air flow look at it there is on vent holes in it my armiture looks like it got HOT its blue and the brush flat pop...
is anyone having problems with the starter gen. on the 084 mine had stop cranking and charging so me and chuck toree it down and fond nothing wrong replaced the sol.and it crank up this time it...
i'm running royal purple for oil with 1 qt lucas oil stableizer my head temp runs 350 to 400 an oil temp is 160 to 200 but that is 2 people and going into a 10-15 mph wind if the wind 20 mph might as...
well i'm still working on the boat i put a 60/28 prop on it i have more top end and better perfromance but i think the rpm's r to high at 3800 so i am still working on this but for the most part the...
well i got my new crank pully 4.25" so now i have a 1.64 reduction and give up i hole shot but the top end is alot better i now get 2100 rpm from the prop it did make a big differents my engine rpm r...
well all is great got it all back together today,with the new 4 pole starter gen,set it up to be able to turn it off if i dont need it to generate will be testing it later today on the river :)
by the way is anyone having trouble getting the drive pully off after u have put it on i did so i used a 3 jaw pully puller and put some pressure on it and it still did not come off i found out to...
well i got anther 084 from chuck coz i sucked a intake gasket but i did blow it up i also have new plan for that 084 it will take some time to get it all to work out so i am going to run this new...
well i it funny that my crank pully is only 3 5/8 so that makes mine 1.93 so we all got a different pully how did that happen so i am hoping that the new one will be 4.25 like we are told i have...
i have been doing the math and here what i found
my pullys are 7 inch on the top and 3.625 on the bottom this makes it to be a 1.93 this is 1865 rpms at the prop
7 by 3.5 is 2.0 = 1800 rpms
7 by 4...
i have the web sites for jets and needle valves they are happy's auto inc and vee web parts they have the best prices and you can buy one or to or ten if u like the idel jet is to small the carb...
here is what i think the bottom pully needs to be 4.5 to 5 inches this will put the prop speed where it needs to be but some of us might have to buy a new prop that are runnning wood props that is i...
hi i have had good luck so far with the jet size i got i my solex i am still running a cht of 350 to380 on cyl 1 the plugs are a light grey and clean i think i will add a 1/4 turn to see if it will...
hay to all sorry i havent been on lately i have been do some more work on my 084 i found that 6 gals of fuel was not going to do it for me i was only getting about 4 hrs of run time so i went to...
ok then i do think i will check for the hottest cyl
i do have a temp gun but it only goes to 999 degree so i will have to do it after i do a short run this way i think i can find the hot cyl ,...
so see u people think i was full if it,but i got the info on the egt from the man at the airplane junk yard and i did look in a couple of engines there a they had the prob 2 in from the head i use...
the simi tractor might do u thr job but i have seen mine as high as 1680 degrees i will see if i can find the web page to the airplane junk yard a post it for all but the exhaust aeem to run between...
before u go buy a new egt/cht go to the local airplane junk yard get one from them mine cost me 150 $ that was cheap u will need to put the egt probe 2 in. from the head to get the right temp to...