Search:

Type: Posts; User: fresh water hunter

Page 1 of 3 1 2 3

Search: Search took 0.14 seconds.

  1. Replies
    1
    Views
    563

    Re: Chuck Rackley

    what a great loss super nice guy rip
  2. Replies
    0
    Views
    630

    48084 with extras

    i am selling my 4a084 bearing were checked good compression unsure on hrs. has new vw carb custom intake, new extra pistons and rods, new jugs, new mag, and extra mag kits, oil cooler. oil temp gauge...
  3. Re: Mini pro 116 got yamaha apex motor going in it thoughts ?

    your hull would be fine as far as the exhaust you will have to jet the carb for a tuned pipe i am running a 70 hp yamaha piped motor 2.75 belt reduction and spin a 68 in three blade warp drive at 8...
  4. Replies
    10
    Views
    4,986

    Re: Snowmobile engine for Mini

    j bird belt drives are 10 hp per belt dr. peck in the builds is using one of the rx1 yamaha engine on here the do make an adapter so you can use a c gearbox
  5. Replies
    6
    Views
    2,323

    Re: 48084

    yes just the red part
  6. Replies
    6
    Views
    2,323

    48084

    i am looking for the front engine mount that mounts to the block for a 4a084 thanks
  7. Replies
    6
    Views
    1,797

    Re: Oh no

    that sucks you need a clockwise rotation prop thats for right hand rotation
  8. Replies
    6
    Views
    1,797

    Re: Oh no

    well if it was an ultra prop you just flip the blocks over
  9. Replies
    6
    Views
    1,797

    Re: Oh no

    so you are running on the end were the stater and pull start pulley are located ?
  10. Replies
    8
    Views
    2,380

    Re: circle s drive

    i built my front mount out of aluminum but set it up to be bolted on both sides my stand is made with 2 angle iron at top and 3/4 by 18 ga. square tube with bracing my question is are the circle s...
  11. Replies
    8
    Views
    2,380

    Re: circle s drive

    I have no mounts on my engine so i have to fab them up also my front mount is flush with top of oil pan. on the circle s drive how far from block out to bolt center and is the bottom of mount flush...
  12. Replies
    8
    Views
    2,380

    Re: circle s drive

    ok thanks now i just need crankshaft center to prop center still waiting on my drive to be built
  13. Replies
    8
    Views
    3,465

    Re: Chain

    check out blankbiplane on u tube he has a nice chaindrive set up and has an email on his video for asking questions
  14. Replies
    8
    Views
    2,380

    circle s drive

    Does any one happen to have any measurements on the circle s drive shaft to shaft center spacing mount bolt center from block out and center to center mounting holes thanks
  15. Replies
    2
    Views
    1,605

    Re: Best engin for the mini 116

    what one are talking about snowmobile or motorcycle?
  16. Replies
    11
    Views
    3,598

    Re: fresh water hunter's hull build

    ya i thought about that and i got the rivets thanks corky
  17. Replies
    11
    Views
    3,598

    Re: fresh water hunter's hull build

    here are some more pics
  18. Replies
    11
    Views
    3,598

    Re: fresh water hunter's hull build

    got a little more done than had to head to florida again best friend is dyeing damn cancer 52 yr old
  19. Replies
    42
    Views
    10,520

    Re: Builders Plans for Mini's ??

    weld the seam then you cut your sides and transom to the height you want and the front rake and weld it all together you can put a bend in the side to increase side strength if using thinner aluminum
  20. Replies
    11
    Views
    3,598

    Re: fresh water hunter's hull build

    it sure does. ran out of wire burnt my last tip off to the weld shop for you guys that weld aluminum i have been using maxel 4943 wire that suff is great flows like 4043 but but way stronger i wont...
  21. Replies
    11
    Views
    3,598

    Re: fresh water hunter's hull build

    it is 12 ft long and 5 ft bottom with 20 in gunnels 76 wide at top of transom all .125th. aluminum
  22. Replies
    11
    Views
    3,598

    Re: fresh water hunter's hull build

    that was day one here is day two lots of welding
  23. Replies
    11
    Views
    3,598

    fresh water hunter's hull build

    Well Its been a long time coming but got some material and here we go i just want to thank every one for there build post's;thumb; it has helped me
  24. Replies
    42
    Views
    11,566

    Re: Mini Air Boat Question/Info needed

    check out airboatpros chucks ecotec builds he did a 300 hp all aluminum 4 cylinder turbo engine on a little boat sweet amount of blades depend on length and hp tq you have to turn them plus pitch...
  25. Replies
    42
    Views
    11,566

    Re: Mini Air Boat Question/Info needed

    do a compression test it will tell you a lot on the engine leaking seals are a 2 stroke enemy how big is the prop i am running a 68 in. on my 70 hp yamaha and yes mix your oil we raced them 250 miles...
Results 1 to 25 of 74
Page 1 of 3 1 2 3