I sent a PM reply to Duane so I'm good now.
Thanks
Type: Posts; User: Cajun_Ag
I sent a PM reply to Duane so I'm good now.
Thanks
I've tried sending 2 pm's to different people and both gave me an error message " invalid form try submitting again" Any idea what's causing this?
If you can find a rotax in a snow mobile that has a provision case meaning you can bolt a gearbox to it then you are WAAAY ahead of the game. I'm using a 900 jetski motor, well trying to anyway. My...
Thanks Chuck I'm not sure at this point if I need them.
I couldn't find a hull close or have one built for less than $3500 which is about $1000 more than I wanted to spend. I got a bid for the Al...
on our bowfishing rigs we use a low psi electric pump. I bypassed the original diaphram pump on my 24hp honda and use an electric pump from NAPA autoparts. I do not reccomend MR Gasket pumps--mine...
Congrats---Time to heat up the grease for the fish fry.
I think it may be more than I need also, but the 4 blade hub should be about perfect. My 3 blade E series (thinest they make) for my bowfishing boat was 600+ so far about 200 more I got this one.
We've made a little progress on the engine. I built an engine stand and we've pretty much sorted out the wiring and eliminated what wasn't needed. I found a 66" powerfin prop on ebay with 5 blade &...
Right now I have it designed as the Rotax bolt pattern mainly because that's what I know. I have the aluminum blank on it's way and will have it machined in the next few weeks so it's not too late to...
As I understand it, you can get the torque increase from a reduction by simply multiplying the torque by the reduction ratio is that correct?
My engine produces 98hp @ 6750rpm, but maximum torque...
I'm on my 5th toyota pickup and have been happy with all of them. It's never put me to walking when I didn't deserve it (E means just enough to make it!---it DOESN'T).
I heard that Chuck. I've had to stall a few projects myself lately.
Hey Chuck any news on the Aero Props
Thomas
Here's what I have found in my searches. These are in no particular order. The problem I've found is cross referencing all the different manufacturers gear designs. I'm going with gates since they...
Duane if your right. Your my new best friend!!
The gates belts website has a design program that you can use. The output is attached & notice the chosen belt requires 861# of belt pull. As I understand it the HTD timing belt design causes it to...
Lately i've been trying to design a reduction drive. If the picture is attached you can see there is not much in the way of mounting choices for any kind of plate type system used on the briggs etc...
Thanks Duane
I dealt with his son Stuart Jr. a couple years back when I built my bowfishing fan. I think several others did as well which leads me to believe that he handled alot of the daily...
HAHA They were all Texas Longhorn fans and ashamed an Texas Aggie got'em and took their picture.
I took a little detour on the way to pick up our new motor.
http://i686.photobucket.com/albums/vv228/Cajun_Ag/Hunting/12-16-09.jpg
In the end we got a limit of ducks and a newly rebuilt engine. I...
Welcome from East Texas
Welcome aboard ;beer;
On the plus side, I now know what a 2 stroke looks like inside and out. :roll:
http://i686.photobucket.com/albums/vv228/Cajun_Ag/Mini%20Airboat/DSC00924.jpg
Well we tore into the engine because of bad compression readings of 43/120/95 and found that one piston broke a ring and scarred the cyl pretty bad. Then we went ahead and broke it down to the crank...
When you get ready for a higher HP test I may be able to help HINT HINT :D