Search:

Type: Posts; User: Corky

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    11
    Views
    177

    Re: 084 Operating Head Temps

    I was thinking of something like a cheap inspection camera...I've got one that could fit in the oil pan plug but I'm wondering just how much oil is being thrown around for either of our ideas...And...
  2. Replies
    11
    Views
    177

    Re: 084 Operating Head Temps

    OK , I had the flow backwards..I never ran mine out of the crate and just stripped everything off...I'm trying to understand why those 4 small shields were in place around the cylinder jugs {the...
  3. Replies
    11
    Views
    177

    Re: 084 Operating Head Temps

    yeah, the factory pulled the air up from the bottom so the original shields probably won't be of much use..
  4. Replies
    11
    Views
    177

    Re: 084 Operating Head Temps

    You know, you might have just answered your own question...Even with the prop it appears there isn't enough airflow to sustain these engines for extended rpms...What if you added a set of fanblades...
  5. Replies
    14
    Views
    1,657

    Re: Modifying the 084 for more horsepower !!

    Great info.. I'll have to look to see just what I've got for pistons and jug sizes... I know the cast rings will seat quicker and the chrome rings tend to break in slower...
  6. Replies
    11
    Views
    177

    Re: 084 Operating Head Temps

    You're right, there's not much room in there to get the squirters shooting in the right direction...Any oil is better than none...As long as you don't bleed it off something that needs the oil down...
  7. Thread: aerokirk's build

    by Corky
    Replies
    270
    Views
    73,316

    Re: aerokirk's build

    Hi Ted,
    Now that I'm up and running I have my circle S tensioner tied up and out of the way...You've been running yours much longer than I have and I was wondering if you've experienced any...
  8. Replies
    11
    Views
    177

    084 Operating Head Temps

    OK, so now that I'm up and running with the daily fishing and general cruising there's some questions...The max operating range for the 084 head temp is supposed to be 475*...And if I stay below 3000...
  9. Re: Oil Pressure Difference between the oil filter and the governor

    So far I haven't had that "dry lifter" start at any point...Strange...I remember the issue with how the block was marked..The "in" on the block was in fact from the oil filter's perspective...So the...
  10. Thread: Corky's Build

    by Corky
    Replies
    528
    Views
    142,565

    Re: Corky's Build

    Thanks guys...I haven't changed anything yet I'm having too much fun !! After work I took a run up to Halifax and back...The river is down from 3.9 to 3.5 it's amazing how different the river is with...
  11. Thread: Corky's Build

    by Corky
    Replies
    528
    Views
    142,565

    Re: Corky's Build

    Here's another thing I've noticed...I did the 084s factory carb modifications as suggested and it hasn't missed a beat !! There's virtually no lag when the throttle is depressed...And it has a good...
  12. Thread: Corky's Build

    by Corky
    Replies
    528
    Views
    142,565

    Re: Corky's Build

    Hi Kent,
    The engine angle is real close..I only get a slight hop at full throttle with just me in the boat...As soon as I touch the stick in either direction it stops..With my wife aboard there's...
  13. Thread: Corky's Build

    by Corky
    Replies
    528
    Views
    142,565

    Re: Corky's Build

    Well, today was the day !!! The water level is good...And the weather is now down from the high humidity 90s...Everything went great...Jumps right up on plane flawlessly with the bow profile I used,...
  14. Replies
    63
    Views
    2,859

    Re: Efi retrofit for the 084 motor

    Ouch...It seems this issue is the biggest problem with the 084...I was wondering about how the heads were going to take the heat...Imagine how hot those valves were to have those red headers glowing...
  15. Replies
    63
    Views
    2,859

    Re: Efi retrofit for the 084 motor

    Hi Bobby good to see you here...I must have guessed correctly, I used the number 3 cylinder for the CHT gauge figuring it would be the hottest {rear jug behind the oil filter}.....The whole header...
  16. Thread: Admin!!

    by Corky
    Replies
    5
    Views
    176

    Re: Admin!!

    Trash was cleaned up and thrown out...You didn't peek at the links did you ??:lol: Just kidding..Cork
  17. Replies
    63
    Views
    2,859

    Re: Efi retrofit for the 084 motor

    That's good news to hear you've got it running on all 4...You deserve it...Great work..
  18. Replies
    63
    Views
    2,859

    Re: Efi retrofit for the 084 motor

    Glad to see everything checked is within working range for the most part...Would the addition of the cam sensor be a worthwhile addition down the road ?? Does that silicone tubing have any structure...
  19. Replies
    63
    Views
    2,859

    Re: Efi retrofit for the 084 motor

    That's still a clean looking delivery system... And those lines need to go where they get it done..Looking good is the second consideration...
  20. Replies
    63
    Views
    2,859

    Re: Efi retrofit for the 084 motor

    Is the case itself waterproof ??? I'm wondering..Even if the case is waterproof is there a chance for humidity/moisture to still affect the board ?? I know you've touched on some type of potting...
  21. Thread: Hello guys

    by Corky
    Replies
    3
    Views
    302

    Re: Hello guys

    Hello and welcome to the site... What's your plans for use of your mini ?? What type of water do you want to run ??
  22. Replies
    76
    Views
    6,243

    Re: new guy looking for ideas

    Good work...That exhaust is close to the front of the prop in it's current form..Probably too close..Not too many choices on what can happen there...Either split them and route them away on each side...
  23. Replies
    69
    Views
    6,189

    Re: A better look for the waterbug

    Looks good..I like the pattern...;thumb;
  24. Replies
    3
    Views
    461

    Re: New 2 person Challenger build.

    Nice, looking forward to the build...;thumb;
  25. Thread: Well

    by Corky
    Replies
    1
    Views
    195

    Re: Well

    Good to see the cover off...Mine hasn't had the cover off since our summer long monsoon from last year..I guess it's time..
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4