Search:

Type: Posts; User: Oran

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    Yes th whirl wind props cost more I have a 3 blade 66 inch adjustable pitch was abut $ 1300
  2. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    I just getting into airboat's but I have not heard of that prop manufacturer mostly whirl wind
  3. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    I. Am getting advice from airtech ultralight they they build air boats with this engine everything is bought and on the airboat I have it at their shop fixing a idle problem. So I hope they know...
  4. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    I am in the middle of up grading to a c box with 3.47 to 1 with a 4 blade 72 inch with a clutch warp drive prop I had a 66 inch 3 blade razor x whirl wind prop it wasn't producing enough thrust .
  5. Replies
    8
    Views
    8,602

    Re: i am finlly geting her together

    I got to go out on the lake with my new boat ran good about 30 mph got right on step I have some adjusting to do to the prop
    I have a little much pitch it will not run dry ground yet and I...
  6. Replies
    8
    Views
    8,602

    Re: i am finlly geting her together

    yes I plan on attaching it with out welding it thanks for your reply and where do you by that kind of wire ?
  7. Replies
    8
    Views
    8,602

    Re: i am finlly geting her together

    what kind of wire should put on the cage . I was told that home Depot sells a rubber coated
    wire that works well
  8. Replies
    8
    Views
    8,602

    Re: i am finlly geting her together

    I hope so . I am at work offshore when I get back home I have to hook up the radiator put the carbs back on hook up the throttle an I will be ready to run the engine
    and then set the...
  9. Replies
    8
    Views
    8,602

    i am finlly geting her together

    11' marty brays hull rotax 582 2.26 .1 belt drive 66" whirl wind prop
  10. Replies
    0
    Views
    5,353

    pic of mini pro build

    I hope they came out this time
  11. Replies
    0
    Views
    5,089

    new mini pro 116 build

    I bought cage already built and trying to figure out how to build the rudder stick and pivet point I know a piece of pipe but I don't know how to make the pivet point if you look at the pic of cage...
  12. Replies
    4
    Views
    9,932

    Re: how make rudder control stick

    do not not know how to post pic. their is no paper clip to attach files just a place t insert image. but I cant figure out how.
  13. Replies
    4
    Views
    9,932

    how make rudder control stick

    I bought this all in one rigging and I am trying to figure out the best way to make the pevit point they have a one inch piece of pipe welded side ways where I guess the evit point would go you can...
  14. mini pro 116 rotax 582 2.62.1 belt drive 67 whirl wind

    new hull from marty brays
  15. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    ok I will us I have been waiting for the hull to be built I had the cage built from air tech ultra lights I have just about everything to start putting it together I am at work for two weeks .
  16. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    I final got my 116.5 hull from marty brays I ordered some frog spit t put o bottom has any body tried spraying it with a HVLP gun does it have to be a special tip I have sprayed some pretty thick...
  17. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    hp on the rotax 582 is 65 and it has 30 hrs on rebuild by rotax rick in Naples Fl.
  18. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    ok I will check it out thanks !!!:-P
  19. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    I have not decided yet I am trying to find out what size prop I will be able to spin with the rotax 582 with a 2.6 1 I think about a three blade warp drive 64"but not sure I hope I get some replies!
  20. Re: getting a mini pro 116 putting a rotax 582 with 2.6 1 cog belt reduction

    all advice and comments are very help full
  21. Re: getting a mini pro 116 putting a rotax 582 with 2.6 1 cog belt reduction

    its all shallow water about two feet deep at best . and south louissiana swamp land with tree's to go around very tight in some places that's why I chose the short hull .
  22. Replies
    25
    Views
    26,587

    Re: rotax 582 with a 2.6x 1 reduction

    I hit a power line one day coming in for a landing i tore the plane up pretty good my wife want let me build another one so two years after the crash I dicided. To put put the engine on a airboat
  23. Re: getting a mini pro 116 putting a rotax 582 with 2.6 1 cog belt reduction

    yes I have did some research for about a two years now and Marty Bray hulls look very good and seem to handle very well I thought about beavers hulls but I have to cross a spot in our lake that...
  24. Replies
    25
    Views
    26,587

    rotax 582 with a 2.6x 1 reduction

    any body seen this set up on a air boat?
  25. Re: getting a mini pro 116 putting a rotax 582 with 2.6 1 cog belt reduction

    also I had this engine in a challenger two air plane and used to run hot if I kept on the ground to long doing run up test I had a radiator from air tech what radiator should I use to get rid of...
Results 1 to 25 of 27
Page 1 of 2 1 2